Test Conditions.  Test 16th June 2023
DitroniX Mains CT Bench Tester, with 3 x CT clamps on single phase to a Warmlite WL42005 Halogen Heater 1200W.
Mains Voltage (~245V), to Greenbrook DAT01A transformer, with single 12V AC output to three Voltage inputs on IPEM (So we see correct readings over three phases).
This is a production IPEM AT90E32 board, with no calibration or corrections applied - just default firmware values.
Note: AC Voltage in, is a single AC supply with common to 1, 2 and 3 input.  Easy way, Short ATM to V1P (All three pads) and Link AC 1, 2 and 3.

------------------------------------------------------------------------------------------------------------------------

DitroniX IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor Board - Development Code

Initialise OLED (If Plugged In)

Register Status and Startup Report
IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor
ESP32 Serial ID: 5499FEEF49C0   Firmware Version: 230616
Board Location: House

Software Optons
----------------
Wi-Fi is Disabled
Domoticz Publishing is Disabled
MQTT Publishing is Disabled
ThingSpeak Publishing is Disabled

EEPROM Check: 20        (Validation OK)

PWM Output is Disabled

DAC Output is Disabled

Peripherals Test
-----------------
Testing RGB LED
Scanning I2C Bus for Devices ...
 * I2C device found at address Decimal 60 = Hex 0x3C OLED
 * I2C device found at address Decimal 80 = Hex 0x50 EEPROM
 * I2C Bus Scan Complete

AC/DC Voltage Input Detected
Connecting to the ATM90E32
ATM90E32 Connected - OK
IPEM Hardware Setup and Power-Up Test - Board Initialized

Register Status and Diagnostic Report
IPEM-1 ATM90E32 ATM90E36 IoT Power Energy Monitor
ESP32 Serial ID: 5499FEEF49C0   Firmware Version: 230616   Location: House

Hardware Configuration for ATM90E32
------------------------------------
AC Voltage Inputs:      Single Input V1 will be used for Current Phase Calculations
Split AC Voltage:       Dual Split-Phase (V1-x-V3) Disabled
CT Current Clamps:      Configured for 1, 2, 3 Phase + 1 Phase (ESP32)
CT4 Current Input:      Configured for ESP32 ADC

[Status Values]
System Status:          S0:0x37E                S1:0xFFFE
Meter Status:           E0:0x20F                E1:0xFF

Mains RMS Voltage
------------------
- - - - - - - - - - - - - - - - - - - - - - - - - - -  
Voltage 1: 245.74 V (Single Line Voltage Selected)     

Calculated RMS Power
---------------------
Power V1*I1: 1204.13 W
Power V1*I2: 1189.38 W
Power V1*I3: 1194.30 W
- - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Power: 3582.81 W (CT1~CT2~CT3)

Active Power (Absorbed or Used by the Load)
--------------------------------------------
Active Power CT1: -1197.98 W    (Export)
Active Power CT2: -1180.80 W    (Export)
Active Power CT3: -1187.90 W    (Export)
- - - - - - - - - - - - - - - - - - - - - -
Total Active Power: -2385.93 W  (Export)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Active Power: -3566.68 W (CT1~CT2~CT3)

Re-Active Power
----------------
ReActive Power CT1: -72.75 VAR
ReActive Power CT2: -68.51 VAR
ReActive Power CT3: -70.68 VAR
- - - - - - - - - - - - - - - - - - - - - - - - -
Total ReActive Power: -143.49 VAR (CT1~CT2~CT3)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Reactive Power: -211.94 W (CT1~CT2~CT3)

Apparent Power (Total Amount of Power Flowing from Source to Load)
-------------------------------------------------------------------
Apparent Power CT1: 1201.35 VA
Apparent Power CT2: 1183.88 VA
Apparent Power CT3: 1191.30 VA
- - - - - - - - - - - - - - - - - - - - - - - - -
Total Apparent Power: 2392.42 VA (CT1~CT2~CT3)
- - - - - - - - - - - - - - - - - - - - - - - - - - - - - -
Calculated Total Apparent Power: 3576.53 W (CT1~CT2~CT3)

Other Power Information
------------------------
Total Fundamental Power: -2382.89 pH(t)

Total Harmonic Power: -3.70

Power Factor
-------------
Power Factor CT1: 0.00 PF
Power Factor CT2: 0.00 PF
Power Factor CT3: 0.00 PF
- - - - - - - - - - - - - - -
Total Power Factor: 0.00 PF

Phase Angle
------------
Phase Angle CT1: 0.00
Phase Angle CT2: 0.00
Phase Angle CT3: 0.00

Other Information
------------------
Chip Temperature: 32.00 °C

Mains Frequency: 50.05 Hz

PCB Temperature Sensor (NTC_IN VN):     31.11 ºC